Tag Archives: Lawrence Livermore National Laboratory

Protecting soldiers from biological and chemical agents with a ‘second skin’ made of carbon nanotubes

There are lots of ‘second skins’ which promise to protect against various chemical and biological agents, the big plus for this ‘skin’ from the US Lawrence Livermore National Laboratory is breathability. From an Aug. 3, 2016 news item on Nanowerk (Note: A link has been removed),

This material is the first key component of futuristic smart uniforms that also will respond to and protect from environmental chemical hazards. The research appears in the July 27 [2016] edition of the journal, , Advanced Materials (“Carbon Nanotubes: Ultrabreathable and Protective Membranes with Sub-5 nm Carbon Nanotube Pores”).

An Aug. 3, 2016 Lawrence Livermore National Laboratory (LLNL) news release (also on EurekAlert), which originated the news item, explains further (Note: Links have been removed),

High breathability is a critical requirement for protective clothing to prevent heat-stress and exhaustion when military personnel are engaged in missions in contaminated environments. Current protective military uniforms are based on heavyweight full-barrier protection or permeable adsorptive protective garments that cannot meet the critical demand of simultaneous high comfort and protection, and provide a passive rather than active response to an environmental threat.

The LLNL team fabricated flexible polymeric membranes with aligned carbon nanotube (CNT) channels as moisture conductive pores. The size of these pores (less than 5 nanometers, nm) is 5,000 times smaller than the width of a human hair [if 1 nm is 1/100,000 or 1/60,000 of a human hair {the two most commonly used measurements} then wouldn’t 5 nm be between 1/20,000 or1/15,000 of a human hair?] .

“We demonstrated that these membranes provide rates of water vapor transport that surpass those of commercial breathable fabrics like GoreTex, even though the CNT pores are only a few nanometers wide,” said Ngoc Bui, the lead author of the paper.

To provide high breathability, the new composite material takes advantage of the unique transport properties of carbon nanotube pores. By quantifying the membrane permeability to water vapor, the team found for the first time that, when a concentration gradient is used as a driving force, CNT nanochannels can sustain gas-transport rates exceeding that of a well-known diffusion theory by more than one order of magnitude.

These membranes also provide protection from biological agents due to their very small pore size — less than 5 nanometers (nm) wide. Biological threats like bacteria or viruses are much larger and typically more than 10-nm in size. Performed tests demonstrated that the CNT membranes repelled Dengue virus from aqueous solutions during filtration tests. This confirms that LLNL-developed CNT membranes provide effective protection from biological threats by size exclusion rather than by merely preventing wetting.

Furthermore, the results show that CNT pores combine high breathability and bio-protection in a single functional material.

However, chemical agents are much smaller in size and require the membrane pores to be able to react to block the threat. To encode the membrane with a smart and dynamic response to small chemical hazards, LLNL scientists and collaborators are surface modifying these prototype carbon nanotube membranes with chemical-threat-responsive functional groups. These functional groups will sense and block the threat like gatekeepers on the pore entrance. A second response scheme also is in development — similar to how living skin peels off when challenged with dangerous external factors. The fabric will exfoliate upon reaction with the chemical agent.

“The material will be like a smart second skin that responds to the environment,” said Kuang Jen Wu, leader of LLNL’s Biosecurity & Biosciences Group. “In this way, the fabric will be able to block chemical agents such as sulfur mustard (blister agent), GD and VX nerve agents, toxins such as staphylococcal enterotoxin and biological spores such as anthrax.”

Current work is directed toward designing this multifunctional material to undergo a rapid transition from the breathable state to the protective state.

“These responsive membranes are expected to be particularly effective in mitigating a physiological burden because a less breathable but protective state can be actuated locally and only when needed,” said Francesco Fornasiero, LLNL’s principal investigator of the project.

The new uniforms could be deployed in the field in less than 10 years.

“The goal of this science and technology program is to develop a focused, innovative technological solution for future chemical biological defense protective clothing,” said Tracee Whitfield, the DTRA [US Defense Threat Reduction Agency] science and technology manager for the Dynamic Multifunctional Material for a Second Skin Program. “Swatch-level evaluations will occur in early 2018 to demonstrate the concept of ‘second skin,’ a major milestone that is a key step in the maturation of this technology.”

The researchers have prepared a video describing their work,

Here’s a link to and a citation for the paper,

Ultrabreathable and Protective Membranes with Sub-5 nm Carbon Nanotube Pores by Ngoc Bui, Eric R. Meshot, Sangil Kim, José Peña, Phillip W. Gibson, Kuang Jen Wu, and Francesco Fornasiero. Advanced Materials Volume 28, Issue 28, pages 5871–5877, July 27, 2016 DOI: 10.1002/adma.201600740 Version of Record online: 9 MAY 2016

© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

This paper is behind a paywall.

New elements named (provisionally)

They say it’s provisionally but I suspect it would take an act of god for a change in the proposed names. From a June 8, 2016 blog posting (scroll down about 25% of the way) on the International Union of Pure and Applied Chemistry (IUPAC) website,

IUPAC is naming the four new elements nihonium, moscovium, tennessine, and oganesson

Following earlier reports that the claims for discovery of these elements have been fulfilled [1, 2], the discoverers have been invited to propose names and the following are now disclosed for public review:

  • Nihonium and symbol Nh, for the element 113,
  • Moscovium and symbol Mc, for the element 115,
  • Tennessine and symbol Ts, for the element 117, and
  • Oganesson and symbol Og, for the element 118.

The IUPAC Inorganic Chemistry Division has reviewed and considered these proposals and recommends these for acceptance. A five-month public review is now set, expiring 8 November 2016, prior to the formal approval by the IUPAC Council.

I can’t figure out how someone from the public might offer a comment about the names.

There’s more from the posting about what kinds of names are acceptable and how the names in this set of four were arrived at,

The guidelines for the naming the elements were recently revised [3] and shared with the discoverers to assist in their proposals. Keeping with tradition, newly discovered elements can be named after:
(a) a mythological concept or character (including an astronomical object),
(b) a mineral or similar substance,
(c) a place, or geographical region,
(d) a property of the element, or
(e) a scientist.
The names of all new elements in general would have an ending that reflects and maintains historical and chemical consistency. This would be in general “-ium” for elements belonging to groups 1-16, “-ine” for elements of group 17 and “-on” for elements of group 18. Finally, the names for new chemical elements in English should allow proper translation into other major languages.

For the element with atomic number 113 the discoverers at RIKEN Nishina Center for Accelerator-Based Science (Japan) proposed the name nihonium and the symbol Nh. Nihon is one of the two ways to say “Japan” in Japanese, and literally mean “the Land of Rising Sun”. The name is proposed to make a direct connection to the nation where the element was discovered. Element 113 is the first element to have been discovered in an Asian country. While presenting this proposal, the team headed by Professor Kosuke Morita pays homage to the trailblazing work by Masataka Ogawa done in 1908 surrounding the discovery of element 43. The team also hopes that pride and faith in science will displace the lost trust of those who suffered from the 2011 Fukushima nuclear disaster.

For the element with atomic number 115 the name proposed is moscovium with the symbol Mc and for element with atomic number 117, the name proposed is tennessine with the symbol Ts. These are in line with tradition honoring a place or geographical region and are proposed jointly by the discoverers at the Joint Institute for Nuclear Research, Dubna (Russia), Oak Ridge National Laboratory (USA), Vanderbilt University (USA) and Lawrence Livermore National Laboratory (USA).

Moscovium is in recognition of the Moscow region and honors the ancient Russian land that is the home of the Joint Institute for Nuclear Research, where the discovery experiments were conducted using the Dubna Gas-Filled Recoil Separator in combination with the heavy ion accelerator capabilities of the Flerov Laboratory of Nuclear Reactions.

Tennessine is in recognition of the contribution of the Tennessee region, including Oak Ridge National Laboratory, Vanderbilt University, and the University of Tennessee at Knoxville, to superheavy element research, including the production and chemical separation of unique actinide target materials for superheavy element synthesis at ORNL’s High Flux Isotope Reactor (HFIR) and Radiochemical Engineering Development Center (REDC).

For the element with atomic number 118 the collaborating teams of discoverers at the Joint Institute for Nuclear Research, Dubna (Russia) and Lawrence Livermore National Laboratory (USA) proposed the name oganesson and symbol Og. The proposal is in line with the tradition of honoring a scientist and recognizes Professor Yuri Oganessian (born 1933) for his pioneering contributions to transactinoid elements research. His many achievements include the discovery of superheavy elements and significant advances in the nuclear physics of superheavy nuclei including experimental evidence for the “island of stability”.

“It is a pleasure to see that specific places and names (country, state, city, and scientist) related to the new elements is recognized in these four names. Although these choices may perhaps be viewed by some as slightly self-indulgent, the names are completely in accordance with IUPAC rules”, commented Jan Reedijk, who corresponded with the various laboratories and invited the discoverers to make proposals. “In fact, I see it as thrilling to recognize that international collaborations were at the core of these discoveries and that these new names also make the discoveries somewhat tangible.”

So, let’s welcome Tennessine, Muscovium, Nihonium, and Oganesson to the table of periodic elements. I imagine Don Lehrer’s Elements Song will be updated soon. In the meantime we have this from ASAP Science, which includes the new elements under their placeholder names (when the addition was first publicized in January 2016. All of the placeholder names start with U,

Enjoy!

An app for nanomaterial risks (NanoRisk)

It seems past time for someone to have developed an app for nanomaterial risks. A Nov. 12, 2015 news item on Nanowerk makes the announcement (Note: A link has been removed),

The NanoRisk App is a guide to help the researcher in the risk assessment of nanomaterials. This evaluation is determined based on the physicochemical characteristics and the activities to be carried out by staff in research laboratories.

The NanoRisk App was developed at the University of Los Andes or Universidad de los Andes in Colombia (there also seems to be one in Chile). From the Nano Risk App homepage,

The NanoRisk App application was developed at the University of Los Andes by the Department of Chemical Engineering and the Department of Electrical and Electronic Engineering, Faculty of Engineering and implemented in cooperation with the Department of Occupational Health at the University of Los Andes. This application focuses on the use of manufactured nanomaterials.

Authors

Homero Fernando Pastrana Rendón MD, MsC, PhD Candidate. Alba Graciela Ávila, Associate Professor, Department of Electrical and Electronic Engineering. Felipe Muñoz Giraldo, Professor Associate Professor, Department of Chemical Engineering, University of Los Andes.

Acknowledgements to Diego Angulo and Diana Fernandez, from the Imagine group, for all the support in the development of this application.

About the App

The app is a guide to help the researcher in the risk assessment of nanomaterials. This evaluation is determined based on the physicochemical characteristics and the activities to be carried out by staff in research laboratories. This is based on nano risk management strategies from various institutions such as the National Institute for Occupational Safety and Health, U.S. (NIOSH), the New Development Organization of Japan Energy and Industrial Technology (NEDO), the European Commission (Nanosafe Program) and the work developed by the Lawrence Livermore National Laboratory (California, USA) in conjunction with the Safety Science Group at the University of Delft in the Netherlands.

RESULT:

The app will estimates the risk at four levels (low, medium, high and very high) for the hazard of the nanomaterial and the probability to be exposed to the material. Then it will recommend measures to contain the risk by applying engineering measures (controlled ventilation system, biosafety cabinet and glovebox).

They have a copyright notice on the page, as well as, instructions on how to access the App and the information.

Carbyne: 40x stiffer than diamond

A material that’s tougher than diamond is the object of interest for researchers at the US Department of Energy’s Lawrence Livermore National Laboratory (LLNL) according to a Sept. 18, 2015 news item by Beth Ellison on Azonano (Note: A link has been removed),

Researchers at Lawrence Livermore National Laboratory (LLNL) have explored a method that uses laser-melted graphite to develop linear chains of carbon atoms.

This material, referred to as carbyne, could possess numerous unique properties, such as modification of the quantity of electrical current passing through a circuit according to the needs of a user. This research could probably lead to the creation of tiny electronics capable of turning on and off at an atomic scale.

A Sept. 17, 2015 LLNL news release (also on EurekAlert) details the research (Note: A link has been removed),

Carbyne is the subject of intense research because of its presence in astrophysical bodies, as well as its potential use in nanoelectronic devices and superhard materials. Its linear shape gives it unique electrical properties that are sensitive to stretching and bending, and it is 40 times stiffer than diamond. It also was found in the Murchison and Allende meteorites and could be an ingredient of interstellar dust.

Using computer simulations, LLNL scientist Nir Goldman and colleague Christopher Cannella, an undergraduate summer researcher from Caltech, initially intended to study the properties of liquid carbon as it evaporates, after being formed by shining a laser beam on the surface of graphite. The laser can heat the graphite surface to a few thousands of degrees, which then forms a fairly volatile droplet. To their surprise, as the liquid droplet evaporated and cooled in their simulations, it formed bundles of linear chains of carbon atoms.

“There’s been a lot of speculation about how to make carbyne and how stable it is,” Goldman said. “We showed that laser melting of graphite is one viable avenue for its synthesis. If you regulate carbyne synthesis in a controlled way, it could have applications as a new material for a number of different research areas, including as a tunable semiconductor or even for hydrogen storage.

“Our method shows that carbyne can be formed easily in the laboratory or otherwise. The process also could occur in astrophysical bodies or in the interstellar medium, where carbon-containing material can be exposed to relatively high temperatures and carbon can liquefy.”

Goldman’s study and computational models allow for direct comparison with experiments and can help determine parameters for synthesis of carbon-based materials with potentially exotic properties.

“Our simulations indicate a possible mechanism for carbyne fiber synthesis that confirms previous experimental observation of its formation,” Goldman said. “These results help determine one set of thermodynamic conditions for its synthesis and could account for its detection in meteorites resulting from high-pressure conditions due to impact.”

Here’s a link to and a citation for the paper,

Carbyne Fiber Synthesis within Evaporating Metallic Liquid Carbon by Christopher B. Cannella and Nir Goldman. J. Phys. Chem. C, 2015, 119 (37), pp 21605–21611 DOI: 10.1021/acs.jpcc.5b03781 Publication Date (Web): July 9, 2015 (print): Sept. 17, 2015

Copyright © 2015 American Chemical Society

This paper is behind a paywall.

Dexter Johnson in a Sept. 18, 2015 posting about the latest carbyne developments on his Nanoclast blog (on the IEEE [Institute for Electrical and Electronics Engineers] website) provides a little history (Note: Links have been removed),

A couple of years ago, a material dubbed carbyne—which is a chain of carbon atoms held together by either double or alternating single and triple atomic bonds—was awarded the title of the world’s strongest material. Later, scientists also demonstrated that it has the unusual property of being able to change from being a conductor to an insulator when it’s stretched by as little as 3 percent.

Here’s an image illustrating the process,

A carbyne strand forms in laser-melted graphite. Carbyne is found in astrophysical bodies and has the potential to be used in nanoelectronic devices and superhard materials. Image by Liam Krauss/LLNL

A carbyne strand forms in laser-melted graphite. Carbyne is found in astrophysical bodies and has the potential to be used in nanoelectronic devices and superhard materials. Image by Liam Krauss/LLNL

Gold and your neurons

Should you need any electrode implants for your neurons at some point in the future, it’s possible they could be coated with gold. Researchers at the Lawrence Livermore National Laboratory (LLNL) and at the University of California at Davis (UC Davis) have discovered that electrodes covered in nanoporous gold could prevent scarring (from a May 5, 2015 news item on Azonano),

A team of researchers from Lawrence Livermore and UC Davis have found that covering an implantable neural electrode with nanoporous gold could eliminate the risk of scar tissue forming over the electrode’s surface.

The team demonstrated that the nanostructure of nanoporous gold achieves close physical coupling of neurons by maintaining a high neuron-to-astrocyte surface coverage ratio. Close physical coupling between neurons and the electrode plays a crucial role in recording fidelity of neural electrical activity.

An April 30, 2015 LLNL news release, which originated the news item, details the scarring issue and offers more information about the proposed solution,

Neural interfaces (e.g., implantable electrodes or multiple-electrode arrays) have emerged as transformative tools to monitor and modify neural electrophysiology, both for fundamental studies of the nervous system, and to diagnose and treat neurological disorders. These interfaces require low electrical impedance to reduce background noise and close electrode-neuron coupling for enhanced recording fidelity.

Designing neural interfaces that maintain close physical coupling of neurons to an electrode surface remains a major challenge for both implantable and in vitro neural recording electrode arrays. An important obstacle in maintaining robust neuron-electrode coupling is the encapsulation of the electrode by scar tissue.

Typically, low-impedance nanostructured electrode coatings rely on chemical cues from pharmaceuticals or surface-immobilized peptides to suppress glial scar tissue formation over the electrode surface, which is an obstacle to reliable neuron−electrode coupling.

However, the team found that nanoporous gold, produced by an alloy corrosion process, is a promising candidate to reduce scar tissue formation on the electrode surface solely through topography by taking advantage of its tunable length scale.

“Our results show that nanoporous gold topography, not surface chemistry, reduces astrocyte surface coverage,” said Monika Biener, one of the LLNL authors of the paper.

Nanoporous gold has attracted significant interest for its use in electrochemical sensors, catalytic platforms, fundamental structure−property studies at the nanoscale and tunable drug release. It also features high effective surface area, tunable pore size, well-defined conjugate chemistry, high electrical conductivity and compatibility with traditional fabrication techniques.

“We found that nanoporous gold reduces scar coverage but also maintains high neuronal coverage in an in vitro neuron-glia co-culture model,” said Juergen Biener, the other LLNL author of the paper. “More broadly, the study demonstrates a novel surface for supporting neuronal cultures without the use of culture medium supplements to reduce scar overgrowth.”

Here’s a link to and a citation for the paper,

Nanoporous Gold as a Neural Interface Coating: Effects of Topography, Surface Chemistry, and Feature Size by Christopher A. R. Chapman, Hao Chen, Marianna Stamou, Juergen Biener, Monika M. Biener, Pamela J. Lein, and Erkin Seker. ACS Appl. Mater. Interfaces, 2015, 7 (13), pp 7093–7100 DOI: 10.1021/acsami.5b00410 Publication Date (Web): February 23, 2015

Copyright © 2015 American Chemical Society

This paper is behind a paywall.

The researchers have provided this image to illustrate their work,

The image depicts a neuronal network growing on a novel nanotextured gold electrode coating. The topographical cues presented by the coating preferentially favor spreading of neurons as opposed to scar tissue. This feature has the potential to enhance the performance of neural interfaces. Image by Ryan Chen/LLNL.

The image depicts a neuronal network growing on a novel nanotextured gold electrode coating. The topographical cues presented by the coating preferentially favor spreading of neurons as opposed to scar tissue. This feature has the potential to enhance the performance of neural interfaces. Image by Ryan Chen/LLNL.

Capturing the particle and the wave: photographing light

On returning to school to get a bachelor’s degree, I registered in a communications course and my first paper was about science, light, and communication. The particle/wave situation still fascinates me (and I imagine many others).

A March 2, 2015 news item on phys.org describes the first successful photography of light as both particle and wave,

Light behaves both as a particle and as a wave. Since the days of Einstein, scientists have been trying to directly observe both of these aspects of light at the same time. Now, scientists at EPFL [École polytechnique fédérale de Lausanne in Switzerland] have succeeded in capturing the first-ever snapshot of this dual behavior.

Quantum mechanics tells us that light can behave simultaneously as a particle or a wave. However, there has never been an experiment able to capture both natures of light at the same time; the closest we have come is seeing either wave or particle, but always at different times. Taking a radically different experimental approach, EPFL scientists have now been able to take the first ever snapshot of light behaving both as a wave and as a particle. The breakthrough work is published in Nature Communications.

A March 2, 2015 EPFL press release (also on EurekAlert), which originated the news item, describes the science and the research,

When UV light hits a metal surface, it causes an emission of electrons. Albert Einstein explained this “photoelectric” effect by proposing that light – thought to only be a wave – is also a stream of particles. Even though a variety of experiments have successfully observed both the particle- and wave-like behaviors of light, they have never been able to observe both at the same time.

A research team led by Fabrizio Carbone at EPFL has now carried out an experiment with a clever twist: using electrons to image light. The researchers have captured, for the first time ever, a single snapshot of light behaving simultaneously as both a wave and a stream of particles particle.

The experiment is set up like this: A pulse of laser light is fired at a tiny metallic nanowire. The laser adds energy to the charged particles in the nanowire, causing them to vibrate. Light travels along this tiny wire in two possible directions, like cars on a highway. When waves traveling in opposite directions meet each other they form a new wave that looks like it is standing in place. Here, this standing wave becomes the source of light for the experiment, radiating around the nanowire.

This is where the experiment’s trick comes in: The scientists shot a stream of electrons close to the nanowire, using them to image the standing wave of light. As the electrons interacted with the confined light on the nanowire, they either sped up or slowed down. Using the ultrafast microscope to image the position where this change in speed occurred, Carbone’s team could now visualize the standing wave, which acts as a fingerprint of the wave-nature of light.

While this phenomenon shows the wave-like nature of light, it simultaneously demonstrated its particle aspect as well. As the electrons pass close to the standing wave of light, they “hit” the light’s particles, the photons. As mentioned above, this affects their speed, making them move faster or slower. This change in speed appears as an exchange of energy “packets” (quanta) between electrons and photons. The very occurrence of these energy packets shows that the light on the nanowire behaves as a particle.

“This experiment demonstrates that, for the first time ever, we can film quantum mechanics – and its paradoxical nature – directly,” says Fabrizio Carbone. In addition, the importance of this pioneering work can extend beyond fundamental science and to future technologies. As Carbone explains: “Being able to image and control quantum phenomena at the nanometer scale like this opens up a new route towards quantum computing.”

This work represents a collaboration between the Laboratory for Ultrafast Microscopy and Electron Scattering of EPFL, the Department of Physics of Trinity College (US) and the Physical and Life Sciences Directorate of the Lawrence Livermore National Laboratory. The imaging was carried out EPFL’s ultrafast energy-filtered transmission electron microscope – one of the two in the world.

For anyone who prefers videos, the EPFL researchers have  prepared a brief description (loaded with some amusing images) of their work,


Here’s a link to and a citation for the research paper,

Simultaneous observation of the quantization and the interference pattern of a plasmonic near-field by L Piazza, T.T.A. Lummen, E Quiñonez, Y Murooka, B.W. Reed, B Barwick & F Carbone. Nature Communications 6, Article number: 6407 doi:10.1038/ncomms7407 Published 02 March 2015

This is an open access paper.

US military wants you to remember

While this July 10, 2014 news item on ScienceDaily concerns DARPA, an implantable neural device, and the Lawrence Livermore National Laboratory (LLNL), it is a new project and not the one featured here in a June 18, 2014 posting titled: ‘DARPA (US Defense Advanced Research Projects Agency) awards funds for implantable neural interface’.

The new project as per the July 10, 2014 news item on ScienceDaily concerns memory,

The Department of Defense’s Defense Advanced Research Projects Agency (DARPA) awarded Lawrence Livermore National Laboratory (LLNL) up to $2.5 million to develop an implantable neural device with the ability to record and stimulate neurons within the brain to help restore memory, DARPA officials announced this week.

The research builds on the understanding that memory is a process in which neurons in certain regions of the brain encode information, store it and retrieve it. Certain types of illnesses and injuries, including Traumatic Brain Injury (TBI), Alzheimer’s disease and epilepsy, disrupt this process and cause memory loss. TBI, in particular, has affected 270,000 military service members since 2000.

A July 2, 2014 LLNL news release, which originated the news item, provides more detail,

The goal of LLNL’s work — driven by LLNL’s Neural Technology group and undertaken in collaboration with the University of California, Los Angeles (UCLA) and Medtronic — is to develop a device that uses real-time recording and closed-loop stimulation of neural tissues to bridge gaps in the injured brain and restore individuals’ ability to form new memories and access previously formed ones.

Specifically, the Neural Technology group will seek to develop a neuromodulation system — a sophisticated electronics system to modulate neurons — that will investigate areas of the brain associated with memory to understand how new memories are formed. The device will be developed at LLNL’s Center for Bioengineering.

“Currently, there is no effective treatment for memory loss resulting from conditions like TBI,” said LLNL’s project leader Satinderpall Pannu, director of the LLNL’s Center for Bioengineering, a unique facility dedicated to fabricating biocompatible neural interfaces. …

LLNL will develop a miniature, wireless and chronically implantable neural device that will incorporate both single neuron and local field potential recordings into a closed-loop system to implant into TBI patients’ brains. The device — implanted into the entorhinal cortex and hippocampus — will allow for stimulation and recording from 64 channels located on a pair of high-density electrode arrays. The entorhinal cortex and hippocampus are regions of the brain associated with memory.

The arrays will connect to an implantable electronics package capable of wireless data and power telemetry. An external electronic system worn around the ear will store digital information associated with memory storage and retrieval and provide power telemetry to the implantable package using a custom RF-coil system.

Designed to last throughout the duration of treatment, the device’s electrodes will be integrated with electronics using advanced LLNL integration and 3D packaging technologies. The microelectrodes that are the heart of this device are embedded in a biocompatible, flexible polymer.

Using the Center for Bioengineering’s capabilities, Pannu and his team of engineers have achieved 25 patents and many publications during the last decade. The team’s goal is to build the new prototype device for clinical testing by 2017.

Lawrence Livermore’s collaborators, UCLA and Medtronic, will focus on conducting clinical trials and fabricating parts and components, respectively.

“The RAM [Restoring Active Memory] program poses a formidable challenge reaching across multiple disciplines from basic brain research to medicine, computing and engineering,” said Itzhak Fried, lead investigator for the UCLA on this project and  professor of neurosurgery and psychiatry and biobehavioral sciences at the David Geffen School of Medicine at UCLA and the Semel Institute for Neuroscience and Human Behavior. “But at the end of the day, it is the suffering individual, whether an injured member of the armed forces or a patient with Alzheimer’s disease, who is at the center of our thoughts and efforts.”

LLNL’s work on the Restoring Active Memory program supports [US] President [Barack] Obama’s Brain Research through Advancing Innovative Neurotechnologies (BRAIN) initiative.

Obama’s BRAIN is picking up speed.

DARPA (US Defense Advanced Research Projects Agency) awards funds for implantable neural interface

I’m not a huge fan of neural implantable devices (at least not the ones that facilitate phone calls directly to and from the brain as per my April 30, 2010 posting; scroll down about 40% of the way) but they are important from a therapeutic perspective. On that  note, the Lawrence Livermore National Laboratory (LLNL) has received an award of $5.6M from the US Defense Advanced Research Projects Agency (DARPA) to advance their work on neural implantable interfaces. From a June 13, 2014 news item on Azonano,

Lawrence Livermore National Laboratory recently received $5.6 million from the Department of Defense’s Defense Advanced Research Projects Agency (DARPA) to develop an implantable neural interface with the ability to record and stimulate neurons within the brain for treating neuropsychiatric disorders.

The technology will help doctors to better understand and treat post-traumatic stress disorder (PTSD), traumatic brain injury (TBI), chronic pain and other conditions.

Several years ago, researchers at Lawrence Livermore in conjunction with Second Sight Medical Products developed the world’s first neural interface (an artificial retina) that was successfully implanted into blind patients to help partially restore their vision. The new neural device is based on similar technology used to create the artificial retina.

An LLNL June 11, 2014 news release, which originated the news item, provides some fascinating insight into the interrelations between various US programs focused on the brain and neural implants,

“DARPA is an organization that advances technology by leaps and bounds,” said LLNL’s project leader Satinderpall Pannu, director of the Lab’s Center for Micro- and Nanotechnology and Center for Bioengineering, a facility dedicated to fabricating biocompatible neural interfaces. “This DARPA program will allow us to develop a revolutionary device to help patients suffering from neuropsychiatric disorders and other neural conditions.”

The project is part of DARPA’s SUBNETS (Systems-Based Neurotechnology for Emerging Therapies) program. The agency is launching new programs to support President Obama’s BRAIN (Brain Research through Advancing Innovative Neurotechnologies) Initiative, a new research effort aimed to revolutionize our understanding of the human mind and uncover ways to treat, prevent and cure brain disorders.

LLNL and Medtronic are collaborating with UCSF, UC Berkeley, Cornell University, New York University, PositScience Inc. and Cortera Neurotechnologies on the DARPA SUBNETS project. Some collaborators will be developing the electronic components of the device, while others will be validating and characterizing it.

As part of its collaboration with LLNL, Medtronic will consult on the development of new technologies and provide its investigational Activa PC+S deep brain stimulation (DBS) system, which is the first to enable the sensing and recording of brain signals while simultaneously providing targeted DBS. This system has recently been made available to leading researchers for early-stage research and could lead to a better understanding of how various devastating neurological conditions develop and progress. The knowledge gained as part of this collaboration could lead to the next generation of advanced systems for treating neural disease.

As for what LLNL will contribute (from the news release),

The LLNL Neural Technology group will develop an implantable neural device with hundreds of electrodes by leveraging their thin-film neural interface technology, a more than tenfold increase over current Deep Brain Stimulation (DBS) devices. The electrodes will be integrated with electronics using advanced LLNL integration and 3D packaging technologies. The goal is to seal the electronic components in miniaturized, self-contained, wireless neural hardware. The microelectrodes that are the heart of this device are embedded in a biocompatible, flexible polymer.

Surgically implanted into the brain, the neural device is designed to help researchers understand the underlying dynamics of neuropsychiatric disorders and re-train neural networks to unlearn these disorders and restore proper function. This will enable the device to be eventually removed from the patient instead of being dependent on it.

This image from LLNL illustrates their next generation neural implant,

This rendering shows the next generation neural device capable of recording and stimulating the human central nervous system being developed at Lawrence Livermore National Laboratory. The implantable neural interface will record from and stimulate neurons within the brain for treating neuropsychiatric disorders.

This rendering shows the next generation neural device capable of recording and stimulating the human central nervous system being developed at Lawrence Livermore National Laboratory. The implantable neural interface will record from and stimulate neurons within the brain for treating neuropsychiatric disorders.

i expect there will be many more ‘brain’ projects to come with the advent of the US BRAIN initiative (funds of $100M in 2014 and $200M in 2015) and the European Union’s Human Brain Project (1B Euros to be spent on research over a 10 year period).

Smart suits for US soldiers—an update of sorts from the Lawrence Livermore National Laboratory

The US military has funded a program named: ‘Dynamic Multifunctional Material for a Second Skin Program’ through its Defense Threat Reduction Agency’s (DTRA) Chemical and Biological Technologies Department and Sharon Gaudin’s Feb. 20,  2014 article for Computer World offers a bit of an update on this project,which was first reported in 2012,

A U.S. soldier is on patrol with his squad when he kneels to check something out, unknowingly putting his knee into a puddle of contaminants.

The soldier isn’t harmed, though, because he or she is wearing a smart suit that immediately senses the threat and transforms the material covering his knee into a protective state that repels the potential deadly bacteria.

Scientists at the Lawrence Livermore National Laboratory, a federal government research facility in Livermore, Calif., are using nanotechnology to create clothing designed to protect U.S. soldiers from chemical and biological attacks.

“The threat is nanoscale so we need to work in the nano realm, which helps to keep it light and breathable,” said Francesco Fornasiero, a staff scientist at the lab. “If you have a nano-size threat, you need a nano-sized defense.”

Fornasiero said the task is a difficult one, and the suits may not be ready for the field for another 10 to 20 years. [emphasis mine]

One option is to use carbon nanotubes in a layer of the suit’s fabric. Sweat and air would be able to easily move through the nanotubes. However, the diameter of the nanotubes is smaller than the diameter of bacteria and viruses. That means they would not be able to pass through the tubes and reach the person wearing the suit.

However, chemicals that might be used in a chemical attack are small enough to fit through the nanotubes. To block them, researchers are adding a layer of polymer threads that extend up from the top of the nanotubes, like stalks of grass coming up from the ground.

The threads are designed to recognize the presence of chemical agents. When that happens, they swell and collapse on top of the nanotubes, blocking anything from entering them.

A second option that the Lawrence Livermore scientists are working on involves similar carbon nanotubes but with catalytic components in a polymer mesh that sits on top of the nanotubes. The components would destroy any chemical agents they come in contact with. After the chemicals are destroyed, they are shed off, enabling the suit to handle multiple attacks.

An October 6, 2012 (NR-12-10-06) Lawrence Livermore National Laboratory (LLNL) news release details the -project and the proponents,

Lawrence Livermore National Laboratory scientists and collaborators are developing a new military uniform material that repels chemical and biological agents using a novel carbon nanotube fabric.

The material will be designed to undergo a rapid transition from a breathable state to a protective state. The highly breathable membranes would have pores made of a few-nanometer-wide vertically aligned carbon nanotubes that are surface modified with a chemical warfare agent-responsive functional layer. Response to the threat would be triggered by direct chemical warfare agent attack to the membrane surface, at which time the fabric would switch to a protective state by closing the CNT pore entrance or by shedding the contaminated surface layer.

High breathability is a critical requirement for protective clothing to prevent heat-stress and exhaustion when military personnel are engaged in missions in contaminated environments. Current protective military uniforms are based on heavyweight full-barrier protection or permeable adsorptive protective overgarments that cannot meet the critical demand of simultaneous high comfort and protection, and provide a passive rather than active response to an environmental threat.

To provide high breathability, the new composite material will take advantage of the unique transport properties of carbon nanotube pores, which have two orders of magnitude faster gas transport rates when compared with any other pore of similar size.

“We have demonstrated that our small-size prototype carbon nanotube membranes can provide outstanding breathability in spite of the very small pore sizes and porosity,” said Sangil Kim, another LLNL scientist in the Biosciences and Biotechnology Division. “With our collaborators, we will develop large area functionalized CNT membranes.”

Biological agents, such as bacteria or viruses, are close to 10 nanometers in size. Because the membrane pores on the uniform are only a few nanometers wide, these membranes will easily block biological agents.

However, chemical agents are much smaller in size and require the membrane pores to be able to react to block the threat. To create a multifunctional membrane, the team will surface modify the original prototype carbon nanotube membranes with chemical threat responsive functional groups. The functional groups on the membrane will sense and block the threat like gatekeepers on entrance. A second response scheme also will be developed: Similar to how a living skin peels off when challenged with dangerous external factors, the fabric will exfoliate upon reaction with the chemical agent. In this way, the fabric will be able to block chemical agents such as sulfur mustard (blister agent), GD and VX nerve agents, toxins such as staphylococcal enterotoxin and biological spores such as anthrax.

The project is funded for $13 million over five years with LLNL as the lead institution. The Livermore team is made up of Fornasiero [Francesco Fornasiero], Kim and Kuang Jen Wu. Other collaborators and institutions involved in the project include Timothy Swager at Massachusetts Institute of Technology, Jerry Shan at Rutgers University, Ken Carter, James Watkins, and Jeffrey Morse at the University of Massachusetts-Amherst, Heidi Schreuder-Gibson at Natick Soldier Research Development and Engineering Center, and Robert Praino at Chasm Technologies Inc.

“Development of chemical threat responsive carbon nanotube membranes is a great example of novel material’s potential to provide innovative solutions for the Department of Defense CB needs,” said Tracee Harris, the DTRA science and technology manager for the Dynamic Multifunctional Material for a Second Skin Program. “This futuristic uniform would allow our military forces to operate safely for extended time periods and successfully complete their missions in environments contaminated with chemical and biological warfare agents.”

The Laboratory has a history in developing carbon nanotubes for a wide range of applications including desalination. “We have an advanced carbon nanotube platform to build and expand to make advancements in the protective fabric material for this new project,” Wu said.

The new uniforms could be deployed in the field in less than 10 years. [emphasis mine]

Since Gaudin’s 2014 article quotes one of the LLNL’s scientists, Francesco Fornasiero, with an estimate for the suit’s deployment into the field as 10 – 20 years as opposed to the “less than 10 years” estimated in the news release, I’m guessing the problem has proved more complex than was first anticipated.

For anyone who’s interested in more details about  US soldiers and nanotechnology,

  • May 1, 2013 article by Max Cacas for Signal Online provides more details about the overall Smart Skin programme and its goals.
  • Nov. 15, 2013 article by Kris Walker for Azonano.com describes the Smart Skin project along with others including the intriguingly titled: ‘Warrior Web’.
  • website for MIT’s (Massachusetts Institute of Technology) Institute for Soldier Nanotechnologies Note: The MIT researcher mentioned in the LLNL news release is a faculty member of the Institute for Soldier Nanotechnologies.
  • website for the Defense Threat Reduction Agency

Interplanetary invaders (dust particles) may be delivery system for water and organics to earth

Researchers at the University of Hawaii and their colleagues in other institutions have determined that interplanetary dust particles (IDP) can deliver solar wind-generated water in addition to the organics which it is known they carry according to a Jan. 24, 2014 news item on ScienceDaily,

Researchers from the University of Hawaii — Manoa (UHM) School of Ocean and Earth Science and Technology (SOEST), Lawrence Livermore National Laboratory, Lawrence Berkeley National Laboratory, and University of California — Berkeley discovered that interplanetary dust particles (IDPs) could deliver water and organics to Earth and other terrestrial planets.

Interplanetary dust, dust that has come from comets, asteroids, and leftover debris from the birth of the solar system, continually rains down on Earth and other Solar System bodies. These particles are bombarded by solar wind, predominately hydrogen ions. This ion bombardment knocks the atoms out of order in the silicate mineral crystal and leaves behind oxygen that is more available to react with hydrogen, for example, to create water molecules.

“It is a thrilling possibility that this influx of dust has acted as a continuous rainfall of little reaction vessels containing both the water and organics needed for the eventual origin of life on Earth and possibly Mars,” said Hope Ishii, new Associate Researcher in the Hawaii Institute of Geophysics and Planetology (HIGP) at UHM SOEST and co-author of the study. This mechanism of delivering both water and organics simultaneously would also work for exoplanets, worlds that orbit other stars. These raw ingredients of dust and hydrogen ions from their parent star would allow the process to happen in almost any planetary system.

The Jan. 24, 2013 University of Hawaii news release (also on EurekAlert), which originated the news item, describes the implications of the research,

Implications of this work are potentially huge: Airless bodies in space such as asteroids and the Moon, with ubiquitous silicate minerals, are constantly being exposed to solar wind irradiation that can generate water. In fact, this mechanism of water formation would help explain remotely sensed data of the Moon, which discovered OH and preliminary water, and possibly explains the source of water ice in permanently shadowed regions of the Moon.

“Perhaps more exciting,” said Hope Ishii, Associate Researcher in HIGP and co-author of the study, “interplanetary dust, especially dust from primitive asteroids and comets, has long been known to carry organic carbon species that survive entering the Earth’s atmosphere, and we have now demonstrated that it also carries solar-wind-generated water. So we have shown for the first time that water and organics can be delivered together.”

The news release provides some background information and a few details about how the research was conducted,

It has been known since the Apollo-era, when astronauts brought back rocks and soil from the Moon, that solar wind causes the chemical makeup of the dust’s surface layer to change. Hence, the idea that solar wind irradiation might produce water-species has been around since then, but whether it actually does produce water has been debated.  The reasons for the uncertainty are that the amount of water produced is small and it is localized in very thin rims on the surfaces of silicate minerals so that older analytical techniques were unable to confirm the presence of water.

Using a state-of-the-art transmission electron microscope, the scientists have now actually detected water produced by solar-wind irradiation in the space-weathered rims on silicate minerals in interplanetary dust particles.  Futher, on the bases of laboratory-irradiated minerals that have similar amorphous rims, they were able to conclude that the water forms from the interaction of solar wind hydrogen ions (H+) with oxygen in the silicate mineral grains.

This recent work does not suggest how much water may have been delivered to Earth in this manner from IDPs.

“In no way do we suggest that it was sufficient to form oceans, for example,” said Ishii. “However, the relevance of our work is not the origin of the Earth’s oceans but that we have shown continuous, co-delivery of water and organics intimately intermixed.”

Here’s a citation for the paper and a link to the abstract,

Detection of solar wind-produced water in irradiated rims on silicate minerals by John Bradley, Hope Ishii, Jeffrey Gillis-Davis, James Ciston, Michael Nielsen, Hans Bechtel, and Michael Martin. Proceedings of the National Academy of Sciences, doi: 10.1073/pnas.1320115111

I believe this paper is behind a paywall.